The Predator special actions are designed for
specific purpose use.
The Predator V is an action designed
for the varmint hunter that shoots from a bench or the lower end
benchrest shooter. It is available in right bolt left port short
action only with 223 or 308 bolfaces. It has a coned bolt, a special
designed bolt knob and a little tighter fit on the bolt. Shown in
top 2 pics
The P1000 is designed for the long range
competition shooter and works great in F-Class also. It is available
in right bolt, left load, right eject only, long and short, 308 and
mag faces. It is available in 1.35 and 1.55 diameters. Both actions
have our standard benchrest 1.115 x 18 TPI tenon to help hold the
heavier longer barrels used in this competition.
There are very few differences between the TAC and the Predator
actions. Here they are:
The bottom cutout on repeaters
The Predator short and long, 308 and magnum boltfaces
have an extended loading box cutout. The cut is 0.130
longer than a standard Remington. It will take Wyatt's Outdoor or HS
Precision extended boxes.
The 223 boltface Predator, TAC30 and TAC300 series
actions have the standard cutout and will take a Remington
box as is.
The Predator XP, short and long action has 6 - 48 TPI
All TAC actions and the Predator Xtreme have 8 - 40
TPI screw holes.
Bolt Knob, all threaded on
Predator and Predator Xtreme have small teardrop.
All TAC actions have larger tactical knob anodized
Predator and Predator Xtreme are matte finished
All TAC actions have black oxide finished stainless.
TAC338 and Predator Xtreme
Same action except color and name. Both have universal
cutout on bottom for either AI magazine or Weatherby
Tactical line of actions are designed for tactical types of use.
They can also be used for long range hunting. They are a stainless
steel drop in replacement for the Remington 700 series actions that
has a black oxide coating. The TAC 30 will fit any stock for a short
action, the TAC 300 for a long. TAC 30 actions have 223 and 308 and
magnum boltfaces, TAC 300 actions have 308 or magnum boltfaces. The
TAC 338 is specifically designed for the 338 Lapua Magnum or 378
Weatherby based cartridges. The TAC 338 is a also a little larger
than the standard long Remington. It is 0.050 larger in diameter and
0.465 longer. That is needed to accommodate the 0.750 diameter bolt
that we feel is necessary for this cartridge. The TAC 408 is
available in both 1.45 and 1.60 diameters. Both the TAC 338 and TAC
408 have no feed lips and use only center feed boxes. Bottom metal
with magazines are available from many sources. The 223 boltface
uses the Sako style extractor, while the others use a modified M16
type. The TAC 338 actions in the right picture are shown with the
standard straight handle as is the TAC 408. All tactical actions
feature a screw-on knob. One piece picatinney rails in standard and
20 moa offset are available. The bolt finish is black iron nitride
We also have our TAC 30 A/W and Spectre short actions.
They have a cutout for the magazine dedicated to use the outstanding
Accuracy International double stack 'Arctic Warfare' magazines. We
have detachable bottom metal for them that utilize this magazine.
The short action does not have feedlips, so a DBM is required. Go to
the accessories page for more information on them. The same bottom
metal works on our other actions or any Remington cutout with the
We make the Spectre in a long action version
which has the same cutout as our TAC300 or Remington 700.
Drop in replacement for popular Remington 700 series actions.
Fits same stocks, triggers and has same nominal headspacing.
Available in short, long and 338 Lapua length. Tactical 30 actions
have 223 and 308 and magnum boltfaces, Tactical 300 actions have 308
or magnum boltfaces. The Tactical 338 is specifically designed for
the 338 Lapua Magnum or 378 Weatherby based cartridges. It has a
little larger footprint, the diameter is 0.050 larger and the length
is 0.465 longer to accommodate the larger boltface. The Tactical 408
is designed to be used for cartridges based on the 408 CheyTac
All action bodies use 416R stainless steel hardened to
41 Rockwell C.
Bolt hole is gun-drilled and then wire edm'ed with the
rails to ensure exact tolerances and size control. Bolt fit to
body is typically .0040 to .0060.
Rails incorporate anti-bind rail for smooth operation
when sliding bolt across port cutouts.
Bolt is factory lapped and either coated with Black
Iron Nitride QPQ to reduce visibility. Bolts are spiral fluted.
Repeaters have standard magazine cutout for use with
Remington parts or we offer a bedding system that uses
proven Accuracy International magazines.
Picatinney rails are available from SPF. Standard
front Remington bases fit both front and rear mounts.
Standard finish is bead blasted matte with a black
Bolt stop is on side above the stock line.
Full round back and smaller port allow for a much
Uses industry standard Remington style firing pin with
The Tactical 30 and Tactical 300 actions use 1.0625-16
tpi, 0.700 inch headspace.
Tactical 338 actions use 1.125-16 tpi, 1.000 inch
Tactical 408 actions use 1.187-16 tpi, 1.100 inch
Now Available in right bolt right port AND left bolt
All CNC machined.
The TAC series has some
upgrades versus the standard Remington 700. Click on the features
button below for a listing of the features that make this action the
must have for your next project.
These are our line of rimfire actions. They all are designed for
the popular 22LR cartridge.
They range in use from
competition 22 rimfire benchrest to tactical trainers to hunting.
The 2500XS meets Sporter class IR50/50 rules, but will not feed
well from the magazine.
The 2500X line of actions is SPF's
attempt at perfection. No stone was left unturned for this line of
actions. The processes and steps that occur in the manufacture of
these are bordering on being ridiculous. We start with the finest
stress relieved 416R steel. We gundrill, pull ream with barrel type
bore reamers and OD turn the blanks to an oversize dimension. At
that point some of the machining happens. We then heat treat the
parts, stress relieve them and then GRIND the OD to the ID. The
threads and face are then put in and engraved. The parts then go to
Melonite to surface harden, make slick and black. They are then
re-ground again and the OD is held within 0.001 diameter,
straightness and roundness. It also gives the attractive black
lettering on the perfectly ground surface. All the internal parts
are made in similar fashions.
The ignition system is a
culmination of all the designs out there with all their issues
fixed. No other action completely controls all the angular
misalignments and rubbing points like this one does. The firing pin
is guided internally in the bolt such that the only contact points
are the pin in the front and a small section in the rear near the
cocking piece. The bolt shroud is located in the body by a pin that
perfectly centers the cocking piece in the trigger such that good
consistent contact is made to the trigger sear. The shroud is then
located to the front bolt half with a setscrew into a spot to
perfectly align the pinholes for the firing pin.
features include easy loading, choice of removable bolt knobs,
trigger hanger for popular Remington pattern triggers, Wire EDM cut
extractors from tool steel and most importantly, tolerances that are
hardly measurable. The 2500X and 2500XS are available in RBRP and
RBLP configurations. The bolt pattern on the bottom is the same as
the Turbo, but the front is slightly longer. The 2500XS uses a Sako
magazine. It is very lightweight and aimed SPECIFICALLY FOR THE
BENCHREST SPORTER CLASS. Don't try to really use this as a repeater.
Feeding from the magazine causes issues and is not recommended and
we will not accept responsibility for anyone using it in this
The 2500XR is a true
repeater using low cost Savage magazines. This is aimed at the
tactical trainer market or for the customer that wants a true high
quality 22 that just isn't available in America anymore. It shares
most of the features of the 2500X line. The OD is not ground on this
action and the surface is all black for the tactical market. It fits
into a standard short action Remington footprint stock. It works in
a standard BDL bottom cut with the door removed. It usually works
with most DBM setups also. The magazine system is self contained and
does not require any stock attachments etc. The area around the
trigger hanger may need relieved to clear the hanger. It works with
most triggers, but call us for our list. The triggers like the
Timney that pivot from the rear do not work with the bolt design.
Available in RBRP only.
We also supply a full line of scope
mounts etc for these. We have them in different offsets and are true
Mil Spec Picatinney.